8.12. Dashboard

Removal and installation
1. Disconnect a wire from the - plug of the rechargeable battery.
2. Remove a steering wheel, casings of a steering column, control levers a heater and floor tunnel casings.
3. Remove a box cap, the airsupercharger and transitional a branch pipe of the airsupercharger.

Fig. 8.32. Details of the new dashboard: 1 – switch of external lighting; 2 – sound signaling device; 3 – screw cap; 4 – screw 6,3x38; 5 – panel; 6 – nozzles; 7 – the arm is left; 8 – the air duct is left; 9 – air duct; 10 – cap; 11 – the air duct is right; 12 – M8 nut; 13 – plug; 14 – laying; 15 – plug; 16 – screw 5x16; 17 – the arm is right; 18 – deflector; 19 – dashboard (lower part); 20 – a nut for the screw; 21 – cap; 22 – washer; 23 – screw 4х16; 24 – slip; 25 – axis; 26 – cover of a ware box; 27 – lighting lamp; 28 – holder of a lamp; 29 – plafond switch; 30 – heater switch; 31 – screw 4х16; 32 – nut; 33 – control unit of a heater; 34 – an overlay of the console with a lamp; 35 – handle; 36 – heater switch handle; 37 – control unit; 38 – switch of the alarm system; 39 – switch of fog lights; 40 – proofreader's handle; 41 – plait of wires of the dashboard; 42 – panel of devices top part; 43 – the nut is lamellar; 44 – combination of devices


4. Turn off nuts of 12 (fig. 8.32) of arms of the 7 and 17 fastening of the dashboard from podkapotny space.
5. Unscrew side screws of fastening of the dashboard in salon.
6. Disconnect blocks of a bunch of wires of the dashboard from the block of safety locks and the resistor of the fan of a heater.
7. Remove a bracket and disconnect the left draft of management of a heater.
8. By means of the screw-driver remove a cap from the left wall of a ware box, through the formed technological window remove a bracket and disconnect the right draft of management of a heater.
9. Nominate to yourself the dashboard in salon.
10. Disconnect draft from the lock of a cowl and draft of the air gate from the carburetor.
11. Take out the dashboard from salon.
12. Install the dashboard upside-down.

Dismantling and assembly
1. Turn out two screws of fastening of the panel 5 (see fig. 8.32) located in the lower part of the dashboard.
2. Remove two caps 3 on the top edge of the panel 5.
3. Unscrew two screws 4.
4. Pull on yourself the lower edge of the panel 5 recorded by latches on the lower part of the dashboard.
5. Disconnect a block of wires from a sound signaling device 2 and a block of wires from the switch of external lighting 1.
6. Remove the panel.
7. Take out side deflectors 18, having pressed hooks.
8. Remove the lamp of lighting 27 located on the top wall of a ware box.
9. Turn out screws 16 and remove arms of the 7 and 17 fastening of the dashboard.
10. Turn out the screw and remove the central air duct 9 and side air ducts 8 and 11.
11. Disconnect blocks of a plait of wires from devices and remove a plait of wires.
12. Uncover a ware box 26 for what push an axis 25 of its collet zone and take out an axis from the nests.
13. Remove heater handles 35 and 36.
14. Turn out screws 31 and remove a slip 34 consoles together with the central deflectors.
15. Unscrew screws and remove the block 33 managements of a heater.
16. Turn off a nut and remove the heater switch 30.
17. Having pressed the corresponding hooks, take out the remained caps, switches, nozzle lamps.
18. Collect the dashboard upside-down.