1.2. Operation

Governing bodies

Fig. 1.3. Governing bodies: 1 – ignition switch; 2 – lever of switching of screen wipers and washers; 3 – switch of lighting of devices; 4 – handle of control of the air gate of the carburetor; 5 – cowl lock drive handle; 6 – switch of a back lamp of fog light; 7 – switch of the alarm system; 8 – side vozdukhoduv (deflectors) of system of ventilation and heating of salon; 9 – switch of heating of back glass; 10 – handle of adjustment of the electroproofreader of headlights; 11 – steering wheel; 12 – lever of the switch of indexes of turn and light of headlights; 13 – key of inclusion of a sound signal; 14 – combination of devices; 15 – switch of external lighting; 16 – sound signaling device; 17 – the place for the radio tape recorder; 18 – central air ducts (deflectors) of system of ventilation and heating of salon; 19 – plug socket; 20 – ware box; 21 – a control lever the air supply gate to legs of the driver and passengers; 22 – control lever gate of an air stream; 23 – lighter; 24 – heating fan electric motor switch; 25 – handle of the parking brake; 26 – gear shifting lever; 27 – accelerator pedal; 28 – brake pedal; 29 – coupling pedal; 30 – control lever deflectors; 31 – the ram for change of a stream of air


The arrangement of governing bodies is shown in fig. 1.3.
The switch of ignition 1 with the anti-theft device has the following provisions of a key:
0 – all consumers are switched off, the key is not taken out, the anti-theft device is not switched on;
I – ignition is included, the key is not taken out, all consumers of energy work according to requirements of operation;
By II – the starter is included, the key is not taken out;
III – switched off ignition, at the taken-out key the anti-theft device is switched on. For switching off of the anti-theft device insert a key into the switch of ignition and, slightly turning a steering wheel to the right-to the left, turn a key in situation 0.
Irrespective of the switch of ignition food on a sound signal, stoplights, plafonds, the lighter, the plug socket, the alarm system driving beam of headlights, the alarm system moves.
The lever 2 switchings of screen wipers and washers has provisions:
I – the cleaner and a washer of a windshield and glass of a door of a back are switched off;
By II – the faltering operating mode of screenwash (unstable situation) is included;
By III – the faltering operating mode of screenwash (the fixed situation) is included;
By IV – the first speed of screenwash (the fixed situation) is included;
V – the second speed of screenwash (the fixed situation) is included;
VI – (on itself) the windshield washer (unstable situation) is included. At the same time also screenwash joins;
By VII – the cleaner of back glass (the fixed situation) is included;
VIII – are included a cleaner and a washer of back glass (unstable situation).
The switch 3 lighting -
devices is energized if external lighting is included. Rotation of the handle lighting of devices joins and their brightness is regulated.
Handle 4 controls of the air gate of the carburetor.
At the extended handle on itself the air gate is closed.
Cowl lock drive handle 5.
When moving the handle up the lock of a cowl opens.
The switch of 6 lamps of fog light in back lamps.
Joins when pressing the switch button. At the same time in the switch button illumination lights up. By repeated pressing there is a switching off of fog light and illumination of the button.
Switch of the 7th alarm system.
By pressing the button the blinking light of indexes of turn and a control lamp on the dashboard is turned on. By repeated pressing the button the alarm system is switched off.
Side deflectors 8 -
have levers 30 of control of gates of deflectors and rams 31 for change of a stream of air.
Switch 9 of heating of back glass.
Joins when pressing the switch button. At the same time in the switch button illumination lights up. Switching off happens by repeated pressing the button.
Handle 10 of adjustment of the electroproofreader of headlights.
Situation "O" corresponds to the equipped mass of the car plus the mass of the driver and passenger on a front seat.
Steering wheel 11.
From a provorachivaniye at the taken-out key of the lock of ignition it is blocked by the anti-theft device.
The lever 12 of the switch of indexes of turn and light of headlights has the following provisions:
I – indexes of turn are switched off, passing beam of headlights is turned on if the switch 15 of external lighting is included in the second fixed provision;
II – are included indexes of the left turn (unstable situation);
III – are included indexes of the left turn (the fixed situation);
IV – are included indexes of the right turn (unstable situation);
V – indexes of the right turn (the fixed situation) are included;
VI – (on itself) turned on driving beam of headlights (unstable situation).
VII – (from itself) turned on driving beam of headlights (the fixed situation) if the switch of external lighting 15 is included in the second fixed provision.
Key 13 of inclusion of a sound signal.
By pressing a key the sound signal joins.
Combination of devices 14.
Contains instrumentations (see the section "Electric equipment".
Switch 15 of external lighting.
By pressing the lower shoulder of a key to the first fixed situation marker lights join, to the second fixed situation – are in addition put under tension of a chain of headlights.
Sound signaling device 16 -
gives a sound signal at inclusion of indexes of turn. If necessary it can be disconnected by the available key.
Nest 17 for the radio tape recorder -
with wires of food and connection of loudspeakers.
The central deflectors 18 -
cope in the same way as side deflectors 8.
The lever of 21 controls of the air supply gate -
in the lower part of interior of the car (see. "Ventilation and heating of salon").
Lever 22 controls of the heater gate.
Regulates the direction of a stream of air (see. "Ventilation and heating").
Lighter 23.
For use press a cartridge, through 20 with it will return to a starting position, ready to application.
Switch 24 electric motors of the fan of a heater.
Has three positions (rotation clockwise) for increase in air supply in interior of the car.
Handle 25 of the parking brake.
For a car zatormazhivaniye move the handle with the parking brake up, for a disinhibition – press the button and lower the handle down.
Gear shifting lever 26.
The scheme of switching is put on the lever handle. For inclusion of transfer of a backing move the lever to the right against the stop, drown down, having pressed the handle, move to the right against the stop and translate back.
At inclusion of transfer of a backing backing light lamps in back lamps join.

Body equipment

Fig. 1.4. Antisolar peaks and mirrors: 1 – peak; 2 – internal mirror; 3 – rychazhok of change of a tilt angle of a mirror; 4 – mirror drive lever; 5 – external mirror


Antisolar peaks of 1 (fig. 1.4) -
protect eyes of the driver and the passenger from counter and side beams of the sun.
Internal mirror 2 -
rear view it is intended for observation of the road behind the car. The mirror can be established by turn a rychazhka 3 in one or the other the fixed provisions. For an exception of the blinding effect of light of headlights of the car going behind change a mirror tilt angle switching a rychazhka.
External mirror 5 -
rear view it is regulated from interior of the car by the drive 4 lever back and forth or turn of the lever around its axis.
The plug socket 19 (see fig. 1.3) -
for connection of a portable lamp it is located in interior of the car under the dashboard on the right.

Fig. 1.5. Ware box: 1 – switch; 2 – plafond; 3 – cover; 4 – latch


Ware box (fig. 1.5) -
it is closed by a cover 3, for its opening pull on yourself the handle of a latch 4. An internal part of a box is lit with a plafond 2. When closing a cover the lamp of a plafond dies away owing to disconnection of contacts of the switch 1.

Fig. 1.6. Ashtrays in a floor casing: 1, 2 – ashtrays; 3 – floor casing cover


Ashtrays (fig. 1.6) -
are established in a floor casing. For opening of an ashtray 1 shift its mobile cover back. To take out an ashtray from a casing nest, pull it for a spring quencher up. The ashtray 2 is located at a back end face of a casing of a floor. For its opening pull on yourself the upper edge of a box. The movement up-back, squeezing a spring quencher, it is possible to take out a box from a casing nest.
Plafond of illumination of salon -
it is located in a ceiling upholstery nest. The plafond own switch and door switches joins when opening the left lobby and right back doors.
Plafond of illumination of a luggage carrier -
it is located in an upholstery in a back part of a ceiling and joins the switch which is available on it.

Ventilation and heating of salon

Fig. 1.7. Heater crane: 1 – case; 2 – cover; 3 – insert; 4 – gate; 5 – laying; 6 – ring; 7 – shaft; 8 – lever


Ventilation and heating of interior of the car is carried out by the driver by giving in interior of the car of air ambient temperature or warmed up by a heater. The design of a heater is executed in such a way that there is an opportunity by the translation of the gate to direct the air arriving from the supercharger through a radiator of a heater or passing a heater radiator. As a result of it there is no need to block access of cooling liquid of the engine to a heater radiator to the autumn, winter and spring periods of operation. With approach of summer hot days access of cooling liquid of the engine to a heater can be blocked by the lever 8 (fig. 1.7) of the crane installed under a cowl in the highway of the bringing heater hose.
Ventilation of salon
External air can come to interior of the car through nozzles of an obduv of a windshield; side 8 (see fig. 1.3) and the central 18th deflectors at open gates of deflectors; the lowered glasses of forward and back doors.
Intake of external air in interior of the car is regulated by the gate operated by the lever 22. When moving the lever 22 the gate of a heater and all stream of air turns to the right, passing a heater radiator, goes to the central and side deflectors and nozzles of a windshield.
The direction of a stream of air via side and central deflectors can be changed, moving the ram 31. The air stream via deflectors can be blocked gates if to move the lever 30 up to an emphasis.
Heating of salon
For ensuring heating of salon:
– turn the handle 8 (fig. 1.7) of the crane located under a cowl, in situation "is opened";
– transfer the lever 22 (fig. 1.3) of control of the gate against the stop to the left side that will provide giving of all stream of air through a heater radiator;
– install the switch 24 electric motors of the fan of a heater on the corresponding operating mode.
For acceleration of heating wind and side glasses:
– block access of air to the lower part of interior of the car, having moved the lever of 21 controls of the air supply gate to legs of the driver and passengers to the left;
– close gates of the central deflectors by moving of the lever 30 to the lower situation;
– direct by means of rams 31 streams of air via side deflectors to glasses of doors.
In process of thawing of glasses move the lever 21 for heating of legs of the driver, passengers on forward and back seats to the right.
The required temperature condition of salon support by movement of the lever 22 controls of the heater gate.

Doors

Fig. 1.8. Opening of doors outside: 1 – button; 2 – external handle; 3 – lock switch


To open doors outside, press the button 1 (fig. 1.8) and pull on yourself a door for the handle 2.

Fig. 1.9. Handles on the internal panel of a door: 1 – armrest; 2 – window regulator handle; 3 – internal handle of opening of a door


To open doors from within, pull on yourself the internal handle 3 (fig. 1.9). For blocking of doors drown the internal handle in facing before click from within.
If, except the left lobby to block all doors abroach, and then to close them, then it will be possible to open them only from within. The lock of a forward left door is blocked from within at the closed door or outside by a key.
The forward left door is recommended to be closed the last not to lock the car with the keys left inside.

Fig. 1.10. Lock of a back door: 1 – lever of blocking of the lock


For prevention of casual opening during the movement the back door is in addition blocked at not drowned internal handle, for this purpose on an open door it is necessary to translate forward against the stop the lever 1 (fig. 1.10) of blocking of the lock and to close a door. It is possible to open a door only outside.
During the movement leave not blocked the left lobby and right back doors that it was possible to open other doors of the car in case of accident. Passengers and the driver have to be fastened by seat belts.
To lower glasses of doors, rotate clockwise the handle 2 (see fig. 1.9) a window regulator. Glass of a back door falls by 1/3 heights of a window. Further applying of effort to the handle will lead to breakage of details of a window regulator.

Cowl

Fig. 1.11. Cowl lock: 1 – lock doggie; 2 – lock fork; 3 – lock case; 4 – spring; 5 – clamp


To open a cowl, move up on yourself the handle 5 (see fig. 1.3) the cowl lock drive. At the same time the doggie of 1 (fig. 1.11) of the lock releases a fork 2 which under the influence of a spring 4 turns, releasing a clamp of the 5th cowl, and raises a back edge of a cowl. After that open a cowl outside a hand, in extreme situation the open cowl is fixed by an emphasis rack automatically. To close a cowl, extend an emphasis rack from deepening and lower a cowl which is fixed by the lock automatically.

Seats
Front seats separate adjustable.

Fig. 1.12. Front seat: 1 – handle of a stopper of a sled of a seat; 2 – handle of adjustment of a tilt angle of a back; 3 – head restraint; 4 – head restraint clamp


For landing on growth pull the handle of 1 stopper of a sled (fig. 1.12) up, move a front seat in the longitudinal direction and lower the handle.
The tilt angle of a back of a front seat changes rotation of the handle 2, the seatback at the same time should not be loaded.
The head restraints 3 established on backs of front seats are not regulated on height. For removal of a head restraint press a clamp 4 and put forward a head restraint up. For installation of a head restraint into place insert its racks into guides and lower down to fixing of a head restraint a clamp latch.
To spread out a front seat, shift it forward and cast away a back rotation of the handle 2 in a comfortable position back. If necessary remove a head restraint and establish a back in one plane with a pillow of a back seat.

Fig. 1.13. Back seat: And – a back seat in usual situation; B – a back seat in the put situation; 1 – draft of the lock of a back; 2 – back; 3 – pillow


The back seat (fig. 1.13) consists of a continuous easily removable pillow of 3 and two separate backs 2. For increase in the area of the luggage compartment it is possible to cast away backs forward for what pull drafts of 1 locks of backs up and lower backs on a pillow.

Seat belts

Fig. 1.14. Lock of seat belts: 1 – belt uvula; 2 – key of disconnection of the lock of a belt; 3 – lock


Cars complete with diagonal and zone seat belts with inertial coils, for the passenger on an average back seat the zone seat belt is provided. To fasten a belt, implant a uvula of 1 (fig. 1.14) into a lock 3 nest before click, without allowing twisting of straps. To unfasten a belt, press 2 locks a key – the strap of a belt will automatically be involved in the inertial coil. At operation clear the polluted straps of belts soap solution, it is impossible to iron straps the iron.
Surely replace a belt if it underwent critical loading in the road accident or has anguishes, attritions and other damages.
Do not fasten a belt of the child sitting on a lap the passenger.

Luggage compartment

Fig. 1.15. Back door pneumosprings: 1 – pneumospring; 2 – finger; 3 – the nut is welded.



Fig. 8.20. Installation of the lock of a door of a back: 1 – back door lock; 2 – draft; 3 – lock switch lead; 4 – hook; 5 – key; 6 – lock switch; 7 – bolt of fastening of a hook; 8 – the washer is gear; 9 – a bolt of fastening of the lock 10 – a lamellar spring; 11 – spring


Fig. 7.55. Plafond of lighting of the luggage compartment: 1 – lens; 2 – switch key; 3 – lamp; 4 – the hook is motionless; 5 – the holder is spring


For access to the luggage compartment insert a key 5 (see fig. 8.20) into the switch 6 of the lock of a door of a back and turn it to the right. The fork of the lock will lift a door so that it can be opened a hand. In open situation the door is kept by pneumosprings of 1 (fig. 1.15). For transportation of goods in the luggage compartment the shelf of a luggage carrier if necessary can be taken out and laid along backs of front seats. For lighting of the luggage compartment the plafond established in a back part of an upholstery of a ceiling is provided. The plafond pressing of a key of the switch of external lighting 15 (see fig. 1.3) and keys 2 (see fig. 7.55) on a plafond joins.

Cleaner and washer of a windshield
Collect the levers enclosed in a set and brushes of a screen wiper among themselves in pairs and install on the car so that brushes were located as it is possible closer to a rubber sealant in the lower part of glass. At inclusion of a screen wiper of a brush have to move from the lower starting position to the top extreme situation and back.
At switching off of a screen wiper of a brush have to return to a starting position. In a faltering operating mode of a screen wiper of a brush during a pause have to stop in a starting position.

Fig. 1.16. Screen wiper and washer: 1 – drafts of a screen wiper; 2 – motor-reducer axis; 3 – crank axis; 4 – motor-reducer; 5 – crank; 6 – plug; 7 – ball; 8 – case


If at inclusion of a screen wiper of a brush from a starting position begin to move down or after switching off of a screen wiper of a brush there pass the starting position and some time move up, so the crank of 5 (fig. 1.16) is established not correctly on an axis 2 motor-reducers. For elimination of such defect after switching off of a screen wiper weaken an inhaling of a nut of fastening of a crank and develop it so that drafts of a screen wiper were located, as shown in fig. 1.16, – draft 1 and a crank 5 have to be on one straight line or the axis 3 cranks can be turned concerning an axis 2 motor-reducers 4 from the specified situation no more than on 10 °. After that again tighten a nut.
In fig. 1.3 possible provisions of the lever 2 switches of cleaners and a washer of a windshield are shown. Plentifully moisten a windshield with water, include a cleaner and check its work on all modes.
Fill a washer reservoir with water; that the pump of a washer did not fail, liquid level in a tank has to be not lower than 20 mm over the bottom plane.
Regulate the direction of a stream of liquid from a jet turn of a ball 7 (see fig. 1.16) by means of a needle.
Before operation of the car in winter time merge water from a washer reservoir and from a washer power supply system for what move the lever 2 (see fig. 1.3) to situation VI and switch off. When using a washer of glass in winter time (at a temperature of -10 °C and below) fill a tank with nonfreezing liquid.

Cleaner and washer of glass of a door of a back

Fig. 1.17. Back door screen wiper: 1 – motor-reducer; 2 – sealant; 3 – the nut is lamellar; 4 – screw 5х16; 5 – washer; 6 – screen wiper brush lever; 7 – slip; 8 – block connecting plait; 9 – panel internal back doors; 10 – back door glass


For purification of glass of a door of a back the cleaner fixed on the internal panel 9 (fig. 1.17) of a door of a back is provided. At installation of the lever 2 (see fig. 1.3) the switch of screen wipers and windscreen washers in situation VII the cleaner brush lever 6 (see fig. 1.17) is set in motion by a motor-reducer 1. The angle of rotation of the lever is equal 112 °.

Fig. 1.18. Washer of a windshield and glass of a door of a back: 1 – windshield washer jets; 2 – washer reservoir; 3 – washer pump; 4 – windshield washer jet pipeline; 5 – electromagnetic valves; 6 – back door glass washer jet; 7 – screw 5х16; 8 – washer 5; 9 – the nut is square


Fig. 1.19. A tank of washers with the pump: 1 – tank; 2 – washer pump; 3 – filter; 4 – tank cover; 5 – pump sealant


At installation of the lever 2 (see fig. 1.3) in situation VIII the electromagnetic valve 5 (fig. 1.18) works and through a jet 6 on glass of a door of a back the washing liquid from the pump 2 (fig. 1.19) moves.

Car radio equipment

Fig. 1.20. Installation of loudspeakers on panels of forward doors: 1 – the nut is flat; 2 – loudspeaker; 3 – lattice; 4 – screw


The car complete set is carried out by the radio equipment by request of consumers. For installation of the autoradio tape recorder in the dashboard of the Izh-21261 car the special place 17 is provided (see fig. 1.3). Places for installation of loudspeakers 2 (fig. 1.20) are provided in the lower part of forward doors. Loudspeakers can be also installed on arms of the shelf of a luggage carrier. You make installation, connection and operation of the radio equipment according to the managements attached to concrete models of autoradio tape recorders and loudspeakers.

Preparation of the car for operation
1. Having received the new car, check performance of work on pre-sale preparation of the car (see the service book).
2. Check existence of the tool and the accessories attached to the car.
3. Attach tips of wires to plugs of the rechargeable battery according to the specified polarity.
4. Install screen wiper levers with brushes.
5. Establish into place external rear-view mirrors.
6. Fill a windshield washer reservoir.
7. Fill the fuel tank with gasoline.
8. Check oil level in cases of the engine, transmission and the back bridge.
9. Check the level of brake fluid in tanks of the main cylinders of a brake and coupling.
10. Check the level of cooling liquid in a broad tank.
Before departure check:
– serviceability of the light alarm system, sound signal, control and measuring and lighting fixtures, screenwash;
– lack of dribble of oil and liquids from car knots.
Then launch the engine and during a trial trip check serviceability of working and parking brake systems, steering, chassis mechanisms.

Installation of registration plates

Fig. 1.21. Fastening of registration plates: 1 – forward registration plate; 2 – the self-cutting bolt; 3 – front bumper; 4 – back registration plate; 5 – plastic nut; 6 – the self-cutting screw; 7 – external panel of a door of a back


The set of details for fastening of registration plates is applied to the car. Forward registration plate 1 (fig. 1.21) fastens to a bumper 3 two self-cutting bolts 2. Before installation of back registration plate 4 insert plastic nuts 5 into two square openings of the external panel 7 doors of a back and fix a sign by the self-cutting screws 6.

Launch of the engine
Launch of the cold engine

Fig. 1.22. Fuel pump of the engine: 1 – lever of manual pumping of fuel


After the long parking of the car before launch of the engine pump up gasoline in the float-operated camera of the carburetor the lever of 1 manual pumping of fuel (fig. 1.22). In the drawing the pump of the engine of fashion is shown. 331, on the car with the engine of fashion. 2106 it is necessary to press the lever to the opposite side. Squeeze out a coupling pedal. Install the gear shifting lever in neutral situation.
Extend to the full the handle 4 (see fig. 1.3) controls of the air gate of the carburetor, insert a key into the switch of ignition and include a starter, without pressing at the same time an accelerator pedal.
If the engine does not begin to work with the first attempt, switch off ignition and through 30–50 with repeatedly include a starter. Duration of inclusion of a starter no more than 10-15 pages.
After launch of the engine release the ignition key which will automatically come back to situation I. Smoothly lower a pedal of coupling and, supporting the steady frequency of rotation of a bent shaft, warm up the engine, gradually utaplivy the handle of control of the air gate of the carburetor. After warming up of the engine during the steady work on the mode of idling it is possible to begin the movement.
At a temperature of air from 0 to -15 °C begin the movement after warming up of the engine within 3–5 min. with a frequency of rotation of a bent shaft which is a little exceeding the minimum steady frequency of rotation on the idling mode. After several minutes of the continuous movement drown to the full the handle of control of the air gate of the carburetor.
To facilitate launch of the engine at a temperature of air below -15 °C, it is recommended to include for several seconds of a headlight for heating of the rechargeable battery.
At a temperature of air below -25 °C for preliminary warming up of the engine before start-up it is possible to use devices for warming up of the engine.
Launch of the hot engine
To launch the hot engine, drown the handle of control of the air gate of the carburetor. Smoothly press a pedal of an accelerator and release it as soon as the engine begins to work.
If the engine very hot and an arrow of the index of temperature of cooling liquid approaches a red zone of a scale, press an accelerator pedal approximately on a third of its course, include a starter and gradually release a pedal as soon as the engine begins to work trouble-free. Do not press sharply an accelerator pedal as it leads to reenrichment of gas mixture and complicates launch of the engine.
For removal of the enriched mix press against the stop a pedal of an accelerator and include a starter. If through 5–7 about the engine does not begin to work trouble-free, repeat start-up in several seconds.
In case of a spontaneous stop of the superheated engine before repeated inclusion of a starter lift and lower the lever of manual pumping of fuel for removal from the power supply system of air and vapors of gasoline interfering normal operation of the engine.

Thermal mode of the engine
In various service conditions of the car it is necessary to support normal thermal power setting as depend on it fuel consumption, power indicators and wear of the main details. Thermal power setting is regulated automatically by the thermostat. At a low temperature of air for providing the normal thermal mode of the engine it is recommended to establish a partition or an insulating cover before a cooling radiator.
If at normal operation of the car during the correct work of knots and elements of the cooling system the engine overheats, check operation of the thermostat and electric fan of the cooling system. The simplest check of operation of the thermostat can be executed to the touch directly on the car. After launch of the cold engine at the serviceable thermostat the taking-away lower hose of a radiator begins to heat up when the arrow of the index of temperature of cooling liquid does not reach prior to the beginning of a red zone of a scale (about 80-85 °C). Earlier or later heating of the taking-away hose of a radiator indicates malfunction of the thermostat.
If the electric fan does not get into gear at a deviation of an arrow of the index of temperature of cooling liquid in a red zone of a scale (100 °C), then the thermoswitch, the relay or the electric fan is faulty.

Running in
During the first 3 thousand km of a run the following is necessary.
1. Before each departure check air pressure in tires, if necessary you bring it to norm.
2. Begin the movement after warming up of the engine with the minimum steady frequency of rotation of a bent shaft.
3. In the period of a running in do not exceed the admissible speeds of the movement of the car specified in the table.

Speed of the movement of the car at a running in, km/h
Run, km
Transfer
I
II
III
IV
V
0-1000
20
45
65
80
80
1000-2000
30
50
80
100
100
2000-3000
40
70
95
120
120

4. Do not load the car more, than it is specified in a technical characteristic. In the period of a running in do not use the car for transportation of the trailer.
5. Avoid whenever possible sharp braking of the car throughout the first hundreds of kilometers of a run for the best extra earnings of frictional overlays of brake shoes.
6. Abstain from long driving with constantly high or low frequency of rotation of a bent shaft of the engine. According to road conditions in due time include low transfer that prevents an engine overload.
7. In the period of a running in avoid training in driving and the movement in severe road conditions (dirt, sand, long rises, etc.).
8. After the run of 1000 km perform the works specified for the coupon No. 1 of the service book at service station.
9. Replace oil in the engine of fashion. 331 after the run of 2000 km, and in the engine of fashion. 2106 – after 3000 km.

Recommendations about driving of the car
Begin the movement on the car with the heated-up engine. If there is no such opportunity, then at a low temperature of air and after the long parking some time on low transfers is recommended to move. In process of warming up of the engine you pass consistently to the highest transfers. Include transfer for a backing only after a full stop of the car.
After a wash of the car or at long movement along the wet road when water gets to brake mechanisms of wheels, during the movement execute several smooth braking to dry disks, drums and brake slips.
When driving the car avoid sharp accelerations and delays – it promotes increase in wear of tires and fuel consumption.
It is necessary to consider that fuel consumption increases also with an insufficient pressure of air in tires, use of the worn-out or polluted spark plugs, engine oils for the engine with bigger viscosity, than it is recommended (for example, use of summer oils in winter time).
Brake mechanisms provide effective braking of the car, nevertheless seek to brake smoothly and moderately. Sharp braking, especially on the wet and slippery road, can become the reason of insufficient coupling of wheels with the road therefore the car will become uncontrollable.

Towage

Fig. 1.23. Eyes for towage: 1 – forward eye; 2 – back eye


For towage eyes ahead of and behind the car (fig. 1.23) are provided.

Fastening of a spare wheel

Fig. 1.24. Fastening of a spare wheel: 1 – arm; 2 – spare wheel; 3 – draft; 4 – hook; 5 – plug; 6 – nut lamb


The spare wheel is placed under half of the luggage compartment, laid on a folding arm of 1 (fig. 1.24) which through draft 3 and the hook 4 fastens to a floor. The spare wheel nestles an arm 1 on a floor at a zavertyvaniye of the nut lamb 6 located in a back part of the luggage compartment. At the same time connection draft hook is involved in the plug 5 and becomes one-piece.